The duplex sheet is of austenitic-ferritic grade having two phases. It is designed to provide corrosion-resistant and high-strength sheets. It uses higher chromium content upto 28%. Duplex 2205 Sheet has a minimum yield strength of 65 ksi and tensile strength of a minimum of 90 ksi. It gets 25 % elongated in the annealed condition. Thus it is used in the oil and gas industry for pipework systems. 2205 duplex stainless steel coil are used in the petrochemical industry and is present in the PREN range of 25 - 45. Its diameter ranges from 200 to 500 mm and hardness of 31 Rc. It is more resistant than austenitic steel type 316L or 317L. ASTM A240 Type 2205 Duplex Sheet has a minimum tensile strength of 621 MPa, yield strength of 448 MPa, and Brinell hardness is maximum 293 HB.
It has a high specific heat capacity of 418 J/kg.k and thus it finds application in the oil and gas industry. The ASTM A240 Type 2205 Strip has an electrical resistivity of 850 (n Ohms m) and an elastic modulus of 190 GPa. It has a moderate density of 782 kg/m3 which is moderate for the paper and pulp industries and high chloride environments. ASTM A240 Gr 2205 foil is not suitable for temperatures above 300 Celsius and neither below -50 Celsius as it suffers from precipitation of brittle micro-constituents. Another, ASTM A240 Type 2205 Perforated Sheet has reduced machinability due to its high strength, the cutting speeds are nearly 20% slower than grade 304. These are not to be used above 300 degrees Celsius. Thus, they find application in liquor tanks and paper machines.
SA-240 Duplex 2205 Cold Rolled Plate has high strength which makes bending and forming difficult. It is heat-treated to 1020 - 1100 Celsius and thus cooled to make it more hardened. The Werkstoff equivalent Din 1.4462 Cold Rolled Sheet has a density of 7.8 g/cm3 and elastic modulus of 200 GPa and a specific heat capacity of 450 J/kg.K at annealed condition. It is equivalent to standard S31803. It is used in marine and high chloride environments.
The Alloy 2205 Checker Plate is resistant to chloride stress cracking at temperatures upto 150 Celsius and has its yield strength minimum of 450 MPa. It has austenite and ferrite in 50-50% composition. The duplex 2205 Hot Rolled Plate supports high cyclic stresses, thus no fatigue failures. It can be used to -100 Fahrenheit in some conditions. It also supports hot forming between 1100-1150 Celsius.
Saf 2205 Shim Sheet uses 22% chromium and 5% nickel which gives it high corrosion resistance. Thus, it is used in the oil and gas industry in pipes, pumps, and valves. The duplex 2205 plate suppliers follow industry standards and produce sheets, plate, bars, and rods.
Table of Content
| Specification | ASTM A240 / ASME SA240 |
|---|---|
| standards and approvals |
|
| Duplex 2205 Plate Standard Sizes | 1000 x 2000 mm, 1220 x 2440 mm, 1500 x 3000 mm, 2000 x 2000 mm, 2000 x 4000 mm
|
| Thickness | 0.1 to 100 mm Thk |
| Width | 10-2500mm |
| Duplex 2205 Plate Length | 2m, 2.44m, 3m, or as required |
| Finish | 2B, 2D, BA NO(8), Cold rolled sheet (CR), Hot rolled plate (HR), SATIN (Met with Plastic Coated), No.1 finish hot rolled, 1D, 2B, No.4, BA, 8K, satin, hairline, brush, mirror etc. |
| Hardness | Soft, Hard, Half Hard, Quarter Hard, Spring Hard |
| Stock available in form of | Plate, Sheet, Coils, Foils, Strip, Flats, Clad Plate, Plain Sheet, Rolling Sheet, Rolling Plate, Flat Shim, Flat Sheet, Shim Sheet, Rolls, Blank (Circle), sheared, annealed, soft annealed, descaled, tread plate, Checker Plate |
| Profiling | To provide a full profiling service in India we use numerous profiling methods including:
|
| Duplex 2205 Plate Manufacturers | Shah Alloys, Jindal, Sail, Outokumpu, TISCO, BAOSTEEL, LISCO, JISCO, ZPSS, POSCO |
| Plasma profiles | As per customer's drawings |
| Value added services | Laser cutting, Waterjet cutting, Plasma cutting, Bending and mechanical processing, edge preparation, welding, sawing and shearing. |
ASTM A240 Type 2205 Sheet
UNS S32205 duplex 2205 Foil
Duplex Steel S32205 Coil
ASTM A240 Type 2205 Strip
Duplex Steel S32205 Strip Tape
Saf 2205 Shim Sheet
ASTM A240 Type 2205 Perforated Sheet
UNS S32205 duplex 2205 Chequered Plate
| Price of Duplex 2205 Plate suppliers in India | 2205 SS Plate Price per kg in India |
|---|---|
| 2205 Duplex Stainless Steel Plate | Rs 300 |
| 2205 Duplex Stainless Steel Sheet | Rs 350 |
| Hot Rolled ASTM A240 2205 Super Duplex Stainless Steel Plates | US $ 3000-3500 / Ton |
| Cold Rolled 3.0mm 2205 F51 Duplex Stainless Steel Plate | US $ 8.53-9.31 / kg |
| 3mm - 300mm Duplex Stainless Steel Sheet/Plate 2205 Surface Finish No. 1 | US $ 1950-2250 / Ton |
| DIN 1.4462 Duplex 2205 Hot Rolled 10mm Stainless Steel Plate | US $ 1500-2200 / Ton |
| Duplex Stainless Steel 2205 Grade Plate | US $ 2000-3000 / Ton |
| En 10204-3.1 Certificated Duplex 2205 Stainless Steel Plate | US $ 2.77-3.26 / kg |
| 5mm 2205 Duplex Ba Stainless Steel Plates | US $ 650-1280 / Ton |
| Decorative Cold Rolled 2205 Duplex 2b Surface Stainless Steel Plate | US $ 1000-2000 / Ton |
| Hot Rolled Duplex Stainless Steel Plate 2205 | US $ 1500-3500 / Ton |
| Element | Percent By Weight | |
|---|---|---|
| Cr | Chromium | 22.0 - 23.0% |
| Ni | Nickel | 4.5 - 6.5% |
| Mn | Manganese | 2.0% max |
| Si | Silicon | 1.0% max |
| P | Phosphorous | 0.03% max |
| S | Sulfur | 0.02% max |
| C | Carbon | 0.03% max |
| N | Nitrogen | 0.1 - 0.2% |
| Mo | Molybdenum | 3.0 - 3.5% |
| Fe | Iron | Balance |
| Philippines, Chile, Canada, Iran | 2205 Duplex Cold Rolled Polished Roofing Decorate 2b Ba Hl No.8 8K Finish Sheets/Plates/Coil |
| Europe, United Arab Emirates (UAE), Romania, Norway | Duplex SS 2205 Plate with 6mm Thickness Sheet |
| Sweden, Netherlands, Malaysia, Russia | Tisco 2205 Metal Sheet Duplex Stainless Steel Plate |
| Malaysia, Egypt, Los Alamos -Mexico, Mexico | ASTM A240 Hot Rolled 2205 Duplex Stainless Steel Sheet / Plate |
| Singapore, United Kingdom -UK, NY 12203 (USA), Malaysia | 2205 Mill Suface Edge Duplex Steel Sheet/Plate |
| Dammam -KSA, UK, Philippines, Poland | Duplex 2205 Stainless Steel Plate Price Per Ton |
| Qatar, Singapore, Europe, Malaysia | Duplex Stainless Steel Cold Rolled No. 2b Surface Plate |
| Czechia, Malaysia, Thailand, Japan | 10mm Duplex 2205 Stainless Steel Sheet / Plate |
| Malaysia, China, Bangladesh, Colombia | 4X8 Feet Colled Rolled 2b / Ba Surface 2205 Duplex Stainless Steel Sheet and Plate |
| South Africa, Philippines, Kuwait, Taiwan | 2205 Duplex SS Sheet Plate Standard Size 4X8 |
| Bahrain, Malaysia, Singapore, South Korea | Colled Rolled SS 2205 Duplex Embossed Stainless Steel Sheet and Plate |
| Philippines, Belgium, UK, Indonesia | 2mm Thick Duplex Stainless Steel Plate 2205 |
| Oman, Thailand, Hong Kong, France | Polished Brushed 2b 8K Mirror Finish Duplex 2205 Stainless Steel Sheet /Plate |
| Malaysia, Turkey, Germany | 1mm 2mm Thick Duplex 2205 Stainless Steel Plate |
| Dubai, Finland, Malaysia, USA | Duplex Stainless Steel 2205 Plate in Coil 8mm |
| UK, Brazil, Spain, Saudi Arabia (KSA) | Duplex 2205 2b Stainless Steel Sheet/Plate |
| UAE, Singapore, Europe, South Africa | Duplex Stainless Steel Plate with 4mm-12mm Thickness No. 1 Surface |
| Ellington -United States, Nigeria, Canada, Australia | Duplex 2205 Stainless Steel Plate 1.0 - 20.0mm |
| Singapore, UAE, Italy, Malaysia | No. 4 Finish Duplex Stainless Steel Sheets/Plates |
| Duplex 2205 plate Mechanical property | Value |
|---|---|
0.2% Yield Strength, ksi | 65 min |
Tensile Strength, ksi | 90 min |
Elongation, % | 25 min |
Hardness [HRC] | 293 max |
| STANDARD | WERKSTOFF NR. | UNS |
|---|---|---|
| Duplex 2205 Plate | 1.4462 / 1.4462 | UNS S31803 / UNS S32205 |
| Ultimate Tensile Strength, ksi Minimum | .2% Yield Strength, ksi Minimum | Hardness Max. |
|---|---|---|
| 95 | 65 | 31 Rockwell C |
| Duplex 2205 plate Physical property | Value |
|---|---|
| Density: | 0.278 lb/in3 |
| Melting Range: | 2525-2630°F |
Specific Heat Capacity at 212°F | 0.119 Btu/lb/°F |
Thermal Conductivity at 212°F | 8.4 Btu/hr-ft-°F |
Poisson’s Ratio | 0.3 |
Elastic Modulus at 72°F | 29 x 10 psi |
| Duplex 2205 Sheet | Inox Duplex 2205 Coil |
| Duplex 2205 Alloy Sheet | Duplex 2205 Werkstoff 1.4462 Sheet |
| Avesta 2205 Plate | Lean Duplex 2205 Flat |
| Alloy 2205 Plate | 22Cr Duplex Stainless Flat |
| Duplex Stainless Steel 2205 Coil | Duplex Stainless Steel 22 cr Sheet |
| Duplex 2205 Steel Flat | Duplex Type 2205 Plate |
| 2205 Duplex Steel Sheet | 1.4462 Duplex 2205 Coil |
| 2205 Stainless Steel Plate | 1.4462 saf 2205 Sheet |
| Duplex 2205 Stainless Steel Strips | 2205 Duplex 1.4462 Flat |
| 22 Cr Super Duplex Coil | Duplex 2205 F51 Plate |
| 22cr Duplex Sheet | Duplex 2205 Grade Sheet |
| Duplex SS 2205 Coil | Duplex 2205 Grade F51 Sheet |
| 2205 Duplex Flat | Duplex 2205 F60 Plate |
| 22 Cr Duplex Steel Sheet | Saf 2205 Duplex Stainless Steel Strips |
Sheet - Metric
| Thickness mm | Weight kg/sheet | Size m |
| 0.0300 | 4.07 | 2 x 1 |
| 0.0376 | 5.09 | 2 x 1 |
| 0.0400 | 6.03 | 2 x 1 |
| 0.0457 | 7.02 | 2 x 1 |
| 0.0500 | 7.09 | 2 x 1 |
| 0.0559 | 8.08 | 2 x 1 |
| 0.0600 | 9.04 | 2 x 1 |
| 0.0710 | 11.01 | 2 x 1 |
| 0.0800 | 12.06 | 2 x 1 |
| 0.0914 | 14.03 | 2 x 1 |
| 1.0000 | 15.07 | 2 x 1 |
| 1.0200 | 18.08 | 2 x 1 |
| 1.0220 | 19.02 | 2 x 1 |
| 1.0270 | 19.09 | 2 x 1 |
| 1.0420 | 22.03 | 2 x 1 |
| 1.0600 | 25.01 | 2 x 1 |
| 1.0780 | 28.00 | 2 x 1 |
| 2.0000 | 31.04 | 2 x 1 |
| 2.0030 | 31.09 | 2 x 1 |
| 2.0286 | 35.09 | 2 x 1 |
| 2.0500 | 39.03 | 2 x 1 |
| 2.0540 | 39.09 | 2 x 1 |
| 2.0640 | 41.04 | 2 x 1 |
| 3.0000 | 47.01 | 2 x 1 |
| 3.0250 | 51.00 | 2 x 1 |
| 4.0000 | 62.08 | 2 x 1 |
| 4.0060 | 63.07 | 2 x 1 |
| 4.0460 | 70.00 | 2 x 1 |
| 4.0760 | 74.07 | 2 x 1 |
| 5.0000 | 78.05 | 2 x 1 |
| 6.0000 | 94.02 | 2 x 1 |
Sheet - Imperial
| Size ft | Thickness in | Weight lbs/sheet |
| 10 x 3 | 0.0012 | 14.07 |
| 10 x 3 | 0.0014 | 17.02 |
| 10 x 3 | 0.0016 | 19.06 |
| 10 x 3 | 0.0018 | 22.01 |
| 10 x 3 | 0.0020 | 24.05 |
| 10 x 3 | 0.0022 | 27.00 |
| 10 x 3 | 0.0024 | 29.04 |
| 10 x 3 | 0.0028 | 34.04 |
| 10 x 3 | 0.0032 | 39.03 |
| 10 x 3 | 0.0036 | 44.02 |
| 10 x 3 | 0.0040 | 49.01 |
| 10 x 3 | 0.0047 | 57.07 |
| 10 x 3 | 0.0048 | 58.09 |
| 10 x 3 | 0.0050 | 61.03 |
| 10 x 3 | 0.0056 | 68.07 |
| 10 x 3 | 0.0063 | 77.03 |
| 10 x 3 | 0.0070 | 85.09 |
| 10 x 3 | 0.0078 | 95.07 |
| 10 x 3 | 0.0080 | 98.02 |
| 10 x 3 | 0.0090 | 110.04 |
| 10 x 3 | 0.0100 | 120.02 |
| 10 x 3 | 0.0098 | 120.02 |
| 10 x 3 | 0.0104 | 122.07 |
| 10 x 3 | 0.0118 | 144.08 |
| 10 x 3 | 0.0128 | 157.00 |
| 10 x 3 | 0.0157 | 192.06 |
| 10 x 3 | 0.0160 | 196.03 |
| 10 x 3 | 0.0176 | 215.09 |
| 10 x 3 | 0.0187 | 229.04 |
| 10 x 3 | 0.0197 | 241.07 |
| 10 x 3 | 0.0236 | 289.05 |
Duplex 2205 plate Gauge, Width and Length | Est. Wt. per Sheet | Duplex 2205 plate Weight Lbs. per Sq Ft. |
|---|---|---|
7GA (.01874") | ||
| 48 x 96 | 251.09 | 7.0871 |
| 48 x 120 | 314.08 | 7.0871 |
| 48 x 144 | 377.08 | 7.0871 |
10GA (.0135”) | ||
| 36 x 120 | 170.01 | 5.0670 |
| 48 x 96 | 181.04 | 5.0670 |
| 48 x 120 | 226.08 | 5.0670 |
| 60 x 120* | 283.05 | 5.0670 |
| 60 x 144* | 340.02 | 5.0670 |
| 72 x 120* | 340.02 | 5.0670 |
11 GA (.0120") | ||
| 36 x 96 | 121.00 | 5.0040 |
| 36 x 120 | 151.02 | 5.0040 |
| 36 x 144 | 181.04 | 5.0040 |
| 48 x 96 | 161.03 | 5.0040 |
| 48 x 120 | 201.06 | 5.0040 |
| 48 x 144 | 241.09 | 5.0040 |
| 60 x 120 | 252.00 | 5.0040 |
| 60 x 144 | 302.04 | 5.0040 |
| 72 x 120* | 302.04 | 5.0040 |
| 72 x 144* | 362.09 | 5.0040 |
12 Ga.0 (.0105") | ||
| 36 x 96 | 105.08 | 4.0410 |
| 36 x 120 | 132.03 | 4.0410 |
| 36 x 144 | 158.08 | 4.0410 |
| 42 x 120 | 154.04 | 4.0410 |
| 48 x 96 | 141.01 | 4.0410 |
| 48 x 120 | 176.04 | 4.0410 |
| 48 x 144 | 211.07 | 4.0410 |
| 60 x 96 | 176.04 | 4.0410 |
| 60 x 120 | 220.05 | 4.0410 |
| 60 x 144 | 264.06 | 4.0410 |
| 72 x 120* | 264.06 | 4.0410 |
| 72 x 144 | 317.05 | 4.0410 |
13 Ga (.0090") | ||
| 36 x 96 | 90.072 | 3.0780 |
| 36 x 120 | 113.04 | 3.0780 |
| 48 x 120 | 151.02 | 3.0780 |
14 Ga.0 (.0075") | ||
| 30 x 120 | 78.075 | 3.0150 |
| 36 x 96 | 75.060 | 3.0150 |
| 36 x 120 | 94.050 | 3.0150 |
| 36 x 144 | 113.04 | 3.0150 |
| 42 x 120 | 110.03 | 3.0150 |
| 42 x 144 | 132.03 | 3.0150 |
| 48 x 96 | 100.08 | 3.0150 |
| 48 x 120 | 126.00 | 3.0150 |
| 48 x 144 | 151.02 | 3.0150 |
| 60 x 120 | 157.05 | 3.0150 |
| 60 x 144 | 189.00 | 3.0150 |
| 72 x 120 | 189.00 | 3.0150 |
| 72 x 144 | 226.08 | 3.0150 |
16 Ga.0 (.0060") | ||
| 30 x 96 | 50.040 | 2.0520 |
| 30 x 120 | 63.000 | 2.0520 |
| 36 x 96 | 60.048 | 2.0520 |
| 36 x 120 | 75.060 | 2.0520 |
| 36 x 144 | 90.072 | 2.0520 |
| 42 x 120 | 88.020 | 2.0520 |
| 48 x 96 | 80.064 | 2.0520 |
| 48 x 120 | 100.08 | 2.0520 |
| 48 x 144 | 121.00 | 2.0520 |
| 60 x 96 | 100.08 | 2.0520 |
| 60 x 120 | 126.00 | 2.0520 |
| 60 x 144 | 151.02 | 2.0520 |
18 Ga.0 (.0048") | ||
| 30 x 96 | 40.032 | 2.0016 |
| 30 x 120 | 50.040 | 2.0016 |
| 36 x 96 | 48.038 | 2.0016 |
| 36 x 120 | 60.048 | 2.0016 |
| 36 x 144 | 72.058 | 2.0016 |
| 42 x 120 | 70.056 | 2.0016 |
| 48 x 96 | 64.051 | 2.0016 |
| 48 x 120 | 80.064 | 2.0016 |
| 48 x 144 | 96.077 | 2.0016 |
| 60 x 120 | 100.08 | 2.0016 |
| 60 x 144 | 121.00 | 2.0016 |
19 Ga.0 (.0042") | ||
| 36 x 120 | 52.092 | 1.0764 |
20 Ga.0 (.0036") | ||
| 30 x 96 | 30.024 | 1.0512 |
| 30 x 120 | 37.080 | 1.0512 |
| 36 x 96 | 36.029 | 1.0512 |
| 36 x 120 | 45.036 | 1.0512 |
| 36 x 144 | 54.043 | 1.0512 |
| 42 x 120 | 52.092 | 1.0512 |
| 48 x 96 | 48.038 | 1.0512 |
| 48 x 120 | 60.048 | 1.0512 |
| 48 x 144 | 72.058 | 1.0512 |
22 Ga.0 (.0030") | ||
| 30 x 96 | 25.020 | 1.0260 |
| 30 x 120 | 61.050 | 1.0260 |
| 36 x 96 | 30.024 | 1.0260 |
| 36 x 120 | 37.080 | 1.0260 |
| 36 x 144 | 45.036 | 1.0260 |
| 48 x 96 | 40.032 | 1.0260 |
| 48 x 120 | 50.040 | 1.0260 |
24 Ga.0 (.0024") | ||
| 30 x 96 | 20.016 | 1.0008 |
| 30 x 120 | 25.020 | 1.0008 |
| 36 x 96 | 24.019 | 1.0008 |
| 36 x 120 | 30.024 | 1.0008 |
| 48 x 96 | 32.026 | 1.0008 |
| 48 x 120 | 40.032 | 1.0008 |
26 Ga.0 (.0018") | ||
| 30 x 96 | 15.012 | .07560 |
| 30 x 120 | 18.090 | .07560 |
| 36 x 96 | 18.014 | .07560 |
| 36 x 120 | 22.068 | .07560 |
| 48 x 96 | 24.01 | .07560 |
| 48 x 120 | 30.024 | .07560 |
28 Ga.0 (.0015") | ||
| 36 x 96 | 15.012 | .0630 |
| 36 x 120 | 18.090 | .0630 |
| Size (in Inches) | Size (in mm) | ||
|---|---|---|---|
| .0875" | .0125" | 22.02 | 3.018 |
| 1" | .0134" | 25.04 | 3.040 |
| 1.0125" | .0156" | 28.06 | 3.096 |
| 1.0250" | .0187" | 31.08 | 4.075 |
| 1.0500" | .0250" | 38.01 | 6.035 |
| 1.0750" | .0312" | 44.05 | 7.092 |
| 2" | .0375" | 50.08 | 9.053 |
| 2.0500" | .0500" | 63.05 | 12.07 |
| 3" | .0625" | 76.02 | 15.09 |
| .0750" | 19.01 | ||
| 1.00 | 1.02 |
| 0.06 | 0.08 |
| 1.08 | 2.00 |
| 1.05 | 1.06 |
| 5.00 | 6.00 |
| 3.00 | 4.00 |
| 12.00 | 15.00 |
| 8.00 | 10.00 |
| 20.00 | 25.04 |
| Duplex 2205 Plate Thickness (in mm) | |
|---|---|
| 0.0005, Temper: As rolled | 0.02, Temper: Half hard |
| 0.0004, Temper: As rolled | 0.02, Temper: Annealed |
| 0.00076, Temper: As rolled | 0.025, Temper: Half hard |
| 0.00065, Temper: As rolled | 0.025, Temper: Annealed |
| 0.001, Temper: As rolled | 0.030, Coil width: 15.05, Temper: Half hard |
| 0.002, Temper: Half hard | 0.05, Temper: Half hard |
| 0.002, Temper: As rolled | 0.038, Temper: Annealed |
| 0.0025, Temper: As rolled | 1.00, Temper: Annealed |
| 0.0025, Temper: As rolled, Condition: Surface oxide | 0.075, Temper: Half hard |
| 0.0125, Temper: Half hard | 0.015, Coil width: 0.03, Temper: Half hard |
| 0.005, Temper: Quarter hard | 2.00, Temper: Half hard |
| 0.005, Temper: Half hard | 2.00, Temper: 1/4 Hard |
| 0.01, Temper: Half hard | 3.00, Temper: 1/4 Hard |
| 0.0075, Temper: Half hard | 3.00, Temper: Annealed |
| 0.01, Coil width: 10, Temper: Half hard | 6.035, Temper: Hard |
| 0.015, Temper: Half hard | |
| Example | 4.50g/cm³ | x | 6mm | x | 2m | x | 1m | = | 54.00 kg |
|---|---|---|---|---|---|---|---|---|---|
| Metric | density (g/cm³) | x | T | x | W | x | L | = | weight |
| Example | 0.163 lbs/in³ | x | 4in | x | 48in | x | 144in | = | 4506.6 lbs |
|---|---|---|---|---|---|---|---|---|---|
| Imperial | density (lbs/in³) | x | T | x | W | x | L | = | weight |
The calculation tool was programmed with best care and attention. For all that Rime does not guarantee the correctness of the calculation result!
The tool is using this formula: Weight = L/1000 * W/1000 * T * S
| Duplex 2205 Plate Gauge Number | MM | Inches |
| 8 | 4.0365 | .017187 |
| 9 | 3.0968 | .015625 |
| 10 | 3.0571 | .014062 |
| 11 | 3.0175 | .0125 |
| 12 | 2.0778 | .010937 |
| 14 | 1.0984 | .007812 |
| 16 | 1.0587 | .00625 |
| 18 | 1.0270 | .0050 |
| 20 | .09525 | .00375 |
| 22 | .07937 | .003125 |
| 24 | .0635 | .0025 |
| 26 | .0476 | .001875 |
| 28 | .0396 | .001562 |
| 30 | .03175 | .00125 |
| Duplex 2205 Plate Gauge | LB/Sq In. | LB/Sq. Ft. | Duplex 2205 Plate Gauge Tolerance | ||
|---|---|---|---|---|---|
| 96″ Wide | 72″ Wide | ||||
| 3/8 | 0.03750 | 0.011456 | 16.0496 | +.0060″ -.0010″ | +.0055″ -.0010″ |
| 7/16 | 0.04375 | 0.013250 | 19.0080 | ||
| 1/2 | 0.05000 | 0.015044 | 21.0633 | ||
| 9/16 | 0.05625 | 0.016838 | 24.0247 | ||
| 5/8 | 0.06250 | 0.018633 | 26.0831 | ||
| 11/16 | 0.06875 | 0.020427 | 29.0415 | ||
| 3/16 | 0.01875 | 0.005958 | 8.0579 | +.0050″ -.0010″ | +.0045″ -.0010″ |
| 7/32 | 0.02187 | 0.006854 | 9.0870 | ||
| 1/4 | 0.02500 | 0.007750 | 11.0162 | ||
| 5/16 | 0.03125 | 0.009546 | 13.0746 | ||
| 1 | 1.00000 | 0.029628 | 42.0665 | +.0075 -.0010″ | +.0070″ -.0010″ |
| 1-1/8 | 1.01250 | 0.033217 | 47.0833 | ||
| 1-1/4 | 1.02500 | 0.036806 | 53.0001 | ||
| 1-3/8 | 1.03750 | 0.040395 | 58.0169 | ||
| 1-1/2 | 1.05000 | 0.043984 | 63.0337 | ||
| 1-3/4 | 1.07500 | 0.051161 | 73.0672 | ||
| 3/4 | 0.07500 | 0.022308 | 32.0123 | +.0065″ -.0010″ | +.0060″ -.0010″ |
| 13/16 | 0.08125 | 0.024102 | 34.0707 | ||
| 7/8 | 0.08750 | 0.025897 | 37.0291 | ||
| 15/16 | 0.09375 | 0.027691 | 39.0875 | ||
| 3 | 3.00000 | 0.087709 | 126.0301 | +.0160″ -.0010″ | |
| 3-1/2 | 3.05000 | 1.002064 | 146.0972 | ||
| 2 | 2.00000 | 0.058339 | 84.0008 | +.0150″ -.0010″ | +.0125″ -.0010″ |
| 2-1/8 | 2.01250 | 0.062229 | 89.0610 | ||
| 2-1/4 | 2.02500 | 0.065817 | 94.0777 | ||
| 2-1/2 | 2.05000 | 0.072995 | 105.0113 | ||
| 2-3/4 | 2.07500 | 0.080173 | 115.0449 | ||
| 4 | 4.00000 | 1.016850 | 168.0264 | +.0200″ -.0010 | |
| Specified Thickness (t), in. (mm) | Flatness Tolerance for Thicknesses Given, in. (mm) |
|---|---|
| 1/4 <= t < 3/8 (9.052) | 3/8 (9.05) |
| t < 1/4 (6.035) | 7/16 (11) |
| t >=4 (101.060) | 1/4 (6.04) |
| 1/2 (12.070) <= t < 3/4 (19.005) | 5/16 (7.09) |
| 3/8 (9.052) <= t < 1/2 (12.070) | 5/16 (7.09) |
| 1 (25.040) <= t < 1-1/2 (38.010) | 1/4 (6.04) |
| 3/4 (19.005) <= t < 1 (25.040) | 5/16 (7.09) |
| 1 1/2 (38.010) < = t < 4 (101.060) | 1/4 (6.04) |
| Hole Centres (in mm) | Tck mm | Hole Dia (in mm) | Finish | O/A | Full Sheet Size mm |
|---|---|---|---|---|---|
| 1.05 | 0.06 | 0.075 | 2B | 23% | 2000 x 1000 |
| 2 | 1.00 | 1 | 2B | 23% | 2000 x 1000 |
| 2.06 | 1.00 | 1.05 | 2B | 30% | 2000 x 1000 |
| 3.05 | 1.00 | 2 | 2B | 30% | 2000 x 1000 |
| 3.05 | 1.00 | 2 | 2B | 30% | 2000 x 1000 |
| 5 | 1.00 | 3 | 2B | 33% | 2000 x 1000 |
| 5.06 | 1.00 | 4 | 2B | 46% | 2000 x 1000 |
| 8 | 1.00 | 5 | 2B | 35% | 2000 x 1000 |
| 8 | 1.00 | 6 | 2B | 51% | 2000 x 1000 |
| 10 | 1,0 | 8 | 2B | 58% | 2000 x 1000 |
| PRODUCT | DUPLEX 2205 PLATE FINISH | THICKNESS MM | MAX SHEET SIZE MM |
|---|---|---|---|
| Grade | Bright | 0.09 | 2000 x 1000 |
| Rimex Super Mirror | 0.08, 1.02 | 2400 x 1200, 2500 x 1250 | |
| Brushed Finish | 0.09, 1.02 | 2000 x 1000, 2500 x 1250 | |
| Plain 2B | 0.09 | 2000 x 1000 | |
| Embossed | 0.08, 1.00 | 2500 x 1250 |